Click for brochure  Bio-Flo® II valve bodies are manufactured from the same forged 316L material as the standard Bio-Pro® forged bodies. All Bio-Flo® II valve sizes are machined from a common raw forging with controlled chemistry per ASME BPE 2007. Bodies are available with clamp or buttweld ends and surface finishes through 10RA. Bio-Flo®
Read more →
Click for brochure  Bio-Pro® forged bodies are manufactured from ASTM A182 GR F316L material with additional controls in regards to chemical content. The sulfur content is maintained to meet and exceed the stringent requirements of BPE.All forgings are solution annealed to maintain the ferrite content to be .05% or less. This low ferrite content
Read more →
Click for brochure Bio-Pro® cast bodies are low carbon stainless steel investment castings that conform to ASTM A351 grade CF3M (316L) material. Castings are solution annealed to provide a sanitary and clean outside finish. Available in sizes 1 1/2” through 6” with either clamp or buttweld end connections. Bio-Pro® cast bodies are available with
Read more →
Click for brochure Bio-Pro® forged bodies are manufactured from ASTM A182 GR F316L material with additional controls in regards to chemical content. The sulfur content is maintained to meet and exceed the stringent requirements of BPE.All forgings are solution annealed to maintain the ferrite content to be .05% or less. This low ferrite content
Read more →
Click for brochure Compact / Lightweight Space-saving. Ease of installation and maintenance and mounts without additional support. Fully Sealed Prevents contaminants from entering the housing while minimizing the risk of leakage between chambers. Durability Longer life expectancy. Higher cycle performance. Air Connections Parallel to piping system for ease and positive installation. Visual Indicator Identifies valve
Read more →
Click for datasheet The DELTA AP1 valve is an aseptic diaphragm valve, which comes in two versions – the Techno and the Econo. Each is available in a hand-operated and a pneumatic actuated version.The valves are equipped with a unique diaphragm fan support to significantly extend diaphragm lifetime.
Click for brochure The L-pattern type diaphragm valve, due to its unique design, minimizes deadlegs in point-of-use outlets. The valve, while installed in a vertical position, serves as a 90-degree elbow. As fluid passes through the body, the valve can be opened to allow provision of uncontaminated samples. The outlet can also serve as
Read more →
Click for brochure The Sterile Access Valve assembly provides access to the horizontal valve body at the lowest cross sectional point. The access port can be used for sampling, steam sterilization, purging or condensate drainage. Ports are furnished with buttweld tube ends, clamp ends, or the utilization of a secondary valve.
Click for brochure Cast Iron Housing – Tough and protective, permits the installation of all standard accessories – travel stops, manual overrides, limit switches, positioners, filter regulators, speed controllers and solenoid valves. Available with optional white epoxy coating. Steel Diaphragm Plates: Superior performance in high pressure service. Positive Stop Provides added safety when manual override
Read more →
Click for brochure Features: Manufactured from 316L stainless steel or other alloys. Mill test summaries furnished with every order. Wide variety of inlet and outlet tubing configurations and polish combinations are available. Design eliminates deadleg inherent in typical mixing or diverting applications. Available with actuated or manual bonnets. Significantly reduces overall spacing requirements
Click for brochure The Zero DL Point-of-Use Valve utilizes the T-pattern design to promote efficient installation when used on clean water loops. The main valve body is machined from a solid block of 316L stainless steel. It’s design improves drainability and eliminates deadlegs within a processing system.
Click for brochure Zero DL T-pattern type valves improve drainability and greatly eliminate deadleg. Typically installed in a horizontal position, this valve also provides for excellent sampling or diverting of critical process fluids throughout the process system. Zero DL™ T-pattern valves are available in sizes ranging from 1/4” through 6”. These valves are machined
Read more →
Click for brochure The Zero DL tank bottom valve, with its conical profile allows for complete drainability and the prevention of deadlegs or entrapment areas. These valves are installed by either bolting or welding to the tank surface. Zero DL™ tank bottom valves are available in sizes ranging from 1/4” through 4”, are manufactured
Read more →
